بال اسکروها رایج ترین اجزای انتقال در ماشین ابزار و ماشین آلات دقیق هستند. وظیفه اصلی آن تبدیل حرکت چرخشی به حرکت خطی یا تبدیل گشتاور به نیروی تکراری محوری است. در عین حال، ویژگی های دقت بالا، برگشت پذیری و راندمان بالا را نیز دارد.
خروج از مرکز: به انحراف مرکز بین طرف ثابت و طرف حمایت کننده اشاره دارد.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60 متر در دقیقه و روانکاری اجباری غبار روغن را می توان 60 در نظر گرفت-100 متر در دقیقه توصیه می شود یک پیچ توخالی سفارش دهید و خنک کننده و روانکاری اجباری را اتخاذ کنید. محیط کار را تمیز نگه دارید و اجازه ندهید گرد و غبار و سایر ناخالصی ها وارد راهرو یا مهره شوند. اگر وضعیت خوب نیست، یک پوشش محافظ به پیچ ها اضافه کنید.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①راندمان انتقال بالا راندمان انتقال انتقال توپ اسکرو به طور کلی 20.92 است-10 درصد و راندمان انتقال گیربکس پیچی کشویی معمولی 20.20 است.-0.40.
②دقت انتقال بالا، حرکت پایدار و بدون پدیده خزیدن. درایو بال اسکرو اساساً اصطکاک غلتشی با مقاومت اصطکاک کوچک است و مقاومت اصطکاک تقریباً هیچ ارتباطی با سرعت حرکت ندارد.
③دویدن در دنده عقب بدون در حال حرکت. پس از اینکه پیچ و مهره از قبل سفت شدند، فاصله محوری را می توان حذف کرد. به این ترتیب هیچ منطقه مرده ای در جهت مخالف وجود ندارد و دقت و صلبیت انتقال محوری بهبود می یابد.
④برگشت پذیر است. از آنجایی که اتلاف اصطکاک بال اسکرو کم است، می توان آن را از حرکت دورانی به حرکت خطی تبدیل کرد و همچنین می توان آن را از حرکت خطی به حرکت چرخشی تبدیل کرد. هم پیچ سرب و هم مهره را می توان به عنوان محرک یا دنبال کننده استفاده کرد.
⑤عمر طولانی. به دلیل از دست دادن اصطکاک کوچک اصطکاک نورد، عمر مفید طولانی است.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
اکنون تماس بگیرید
E-mail: sales@gyballscrew.com Tel(واتس اپ): به علاوه 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
